Skip to content

Volume IIIElectronics

4.P — Worked Problems: Signals and Systems ​

Problem 1 — Classify a signal ​

For x(t)=5e^{-2t}u(t): find the energy, the power, and classify it. Then do the same for x(t)=3\cos(100t).

Solution

First signal.

E=\int_0^\infty|5e^{-2t}|^2dt=25\int_0^\infty e^{-4t}dt=25\left[\frac{e^{-4t}}{-4}\right]_0^\infty=\frac{25}{4}=6.25\ \text{J}

Finite energy. Power is energy divided by infinite time, so P=0.

An energy signal.

Second signal. Energy diverges, since \cos^2 does not decay. Power over one period:

P=\frac1T\int_0^T9\cos^2(100t)dt=9\times\frac12=4.5\ \text{W}

using \overline{\cos^2}=\tfrac12.

A power signal.

Why the classification matters. The Fourier transform of the first exists as an ordinary function, 5/(2+j\omega). The second's does not — it needs impulses, 3\pi[\delta(\omega-100)+\delta(\omega+100)]. Knowing which kind of signal you have tells you whether the mathematics will be clean or will need distributions.

Problem 2 — Test a system's properties ​

Classify y[n]=nx[n] for linearity, time-invariance, causality, stability and memory.

Solution

Linear? With input ax_1+bx_2:

y = n(ax_1[n]+bx_2[n]) = a(nx_1[n])+b(nx_2[n]) = ay_1+by_2 \ ✓

Linear.

Time-invariant?

  • Delayed input: y_1[n] = n\,x[n-k]
  • Delayed output: y_2[n]=y[n-k]=(n-k)x[n-k]

n\,x[n-k] \ne (n-k)x[n-k] \ ✗

Not time-invariant.

Causal? Output at n uses input at n only ✓. Causal.

Stable? Bounded input |x[n]|\le M gives |y[n]|=|n|M, which grows without limit as n increases ✗. Unstable.

Memoryless? Uses only the present input ✓. Memoryless.

The summary is unusual and instructive: linear, causal, memoryless, but neither time-invariant nor stable. Because it is not LTI, none of the impulse-response machinery of Chapters 4.3 to 4.6 applies. There is no transfer function for this system, and any attempt to write one is a mistake.

Problem 3 — Convolution by hand ​

Convolve x[n]=\{2,1,3\} starting at n=0 with h[n]=\{1,2\}.

Solution

y[n]=\sum_kx[k]h[n-k]

n=0: only k=0. y[0]=2\times1=2

n=1: k=0 gives x[0]h[1]=2\times2=4; k=1 gives x[1]h[0]=1\times1=1. y[1]=5

n=2: k=1 gives 1\times2=2; k=2 gives 3\times1=3. y[2]=5

n=3: k=2 gives 3\times2=6. y[3]=6

y[n]=\{2,5,5,6\}

Check the length: 3+2-1=4 ✓.

Check the area: \sum x=6, \sum h=3, product 18. 2+5+5+6=18 ✓.

Check by polynomial multiplication:

(2+z+3z^2)(1+2z)=2+z+3z^2+4z+2z^2+6z^3=2+5z+5z^2+6z^3 \ ✓

The polynomial check is the fastest way to verify any hand convolution, and it is the same operation as long multiplication without carries.

Problem 4 — Convolution of two rectangles ​

Convolve two rectangular pulses of height 1: one of width 2 (from 0 to 2) and one of width 3 (from 0 to 3). Sketch the result and give its equation.

Solution

Predict before computing. Widths add: the result runs from 0 to 5. Areas multiply: total area is 2\times3=6. Peak height is the smaller width, 2.

Compute region by region. The flipped 3-wide pulse slides across the 2-wide one.

0\le t\le2 — sliding in. Overlap grows linearly:

y(t)=\int_0^t 1\,d\tau = t

At t=2: y=2 ✓ matching the predicted peak.

2\le t\le3 — fully overlapped. The 2-wide pulse sits entirely inside the 3-wide window:

y(t)=2

A flat top of length 1, which is the difference of the widths.

3\le t\le5 — sliding out:

y(t)=5-t

At t=5: y=0 ✓.

A trapezoid, rising for 2, flat for 1, falling for 2.

Check the area: \tfrac12(2)(2)+2(1)+\tfrac12(2)(2)=2+2+2=6 ✓.

The general result: two rectangles of widths W_1 and W_2 convolve into a trapezoid with total width W_1+W_2, a flat top of width |W_1-W_2|, and height \min(W_1,W_2). When the widths are equal the flat top vanishes and you get a triangle — which is the classic textbook case, and now you can see it is the special case rather than the general one.

Problem 5 — Fourier series of a pulse train ​

Find the Fourier series coefficients of a rectangular pulse train: amplitude A, pulse width \tau, period T.

Solution

Take the pulse centred on t=0, from -\tau/2 to \tau/2, so the signal is even and only cosines appear.

c_n=\frac1T\int_{-\tau/2}^{\tau/2}Ae^{-jn\omega_0t}dt = \frac AT\left[\frac{e^{-jn\omega_0t}}{-jn\omega_0}\right]_{-\tau/2}^{\tau/2}

=\frac{A}{T}\cdot\frac{e^{jn\omega_0\tau/2}-e^{-jn\omega_0\tau/2}}{jn\omega_0}=\frac{A}{T}\cdot\frac{2\sin(n\omega_0\tau/2)}{n\omega_0}

With \omega_0=2\pi/T:

c_n=\frac{A\tau}{T}\cdot\frac{\sin(n\pi\tau/T)}{n\pi\tau/T}=\frac{A\tau}{T}\,\text{sinc}\!\left(\frac{n\tau}{T}\right)

The envelope is a sinc, sampled at the harmonic frequencies. This is the discrete version of the rectangle-to-sinc pair.

Worked numbers. A=1, \tau=1 ms, T=10 ms, so the duty cycle is 10% and f_0=100 Hz.

c_0=\frac{1\times1}{10}=0.1

which is the average value, correctly 10% ✓.

c_1=0.1\,\text{sinc}(0.1)=0.1\times\frac{\sin(0.1\pi)}{0.1\pi}=0.1\times0.9836=0.0984

Zeros of the envelope occur where n\tau/T is an integer, so at n=10,20,30,\ldots — that is, at 1 kHz, 2 kHz, 3 kHz.

The practical reading: the first spectral null is at 1/\tau. A narrower pulse pushes the null higher, so the spectrum is wider. This is why a fast digital clock edge radiates far beyond its own frequency, and why deliberately slowing a signal's edges (Chapter 3.6) reduces emissions — the null moves down and takes the high-frequency energy with it.

Problem 6 — Square wave harmonics and Gibbs ​

A 1 kHz square wave of amplitude 1 V. Give the first four non-zero harmonics with amplitudes, the total harmonic power, and the fraction carried by the fundamental.

Solution

b_n=\frac{4}{\pi n} \ (n \text{ odd})

HarmonicFrequencyAmplitude
11 kHz4/\pi = 1.273 V
33 kHz0.424 V
55 kHz0.255 V
77 kHz0.182 V

Note the fundamental's amplitude exceeds 1 V, which surprises people. It is correct: the higher harmonics subtract near the peak to flatten the top, so the fundamental alone must overshoot.

Total power. A square wave of amplitude 1 has x^2=1 everywhere, so P=1 W (into 1 Ω).

Fundamental's power:

P_1=\frac{(1.273)^2}{2}=0.810\ \text{W}

81% of the power is in the fundamental alone.

Cumulative:

Through harmonicPowerFraction
10.81081.0%
30.90090.0%
50.93393.3%
70.95095.0%

Check the series converges to 1:

\sum_{n\ \text{odd}}\frac{1}{2}\left(\frac{4}{\pi n}\right)^2=\frac{8}{\pi^2}\sum_{n\ \text{odd}}\frac{1}{n^2}=\frac{8}{\pi^2}\cdot\frac{\pi^2}{8}=1 \ ✓

using the known sum 1+\frac19+\frac1{25}+\cdots=\pi^2/8.

The engineering consequence. Filtering a square wave to just above the fundamental leaves 81% of the power and a clean sine. But the 9th harmonic at 9 kHz is still 0.14 V — 11% of the fundamental — so a "1 kHz" square wave demands a system with bandwidth well past 10 kHz to keep its shape. That is why a square wave is the standard test for an amplifier's bandwidth: the corners tell you immediately what the high-frequency response is doing.

Problem 7 — Fourier transform of a decaying exponential ​

Find and interpret the transform of x(t)=e^{-at}u(t) with a>0.

Solution

X(\omega)=\int_0^\infty e^{-at}e^{-j\omega t}dt=\int_0^\infty e^{-(a+j\omega)t}dt=\left[\frac{e^{-(a+j\omega)t}}{-(a+j\omega)}\right]_0^\infty=\frac{1}{a+j\omega}

Magnitude:

|X(\omega)|=\frac{1}{\sqrt{a^2+\omega^2}}

Phase:

\angle X(\omega)=-\arctan\frac{\omega}{a}

Interpretation. At \omega=0: magnitude 1/a, the largest value. At \omega=a: magnitude 1/(a\sqrt2) — down by 3 dB, so \omega=a is the half-power frequency. Beyond that it falls as 1/\omega, which is 20 dB per decade.

This is exactly an RC low-pass filter's response with a=1/RC, and it should be, because e^{-t/RC} is that filter's impulse response.

The reciprocal relationship again. A fast decay (large a) gives a wide spectrum; a slow decay gives a narrow one. Duration in time and width in frequency trade against each other, always.

Phase check: at \omega=a the phase is -45°, and at \omega\to\infty it approaches -90°. Those are exactly the numbers a first-order filter's Bode plot shows in Chapter 6.5.

Problem 8 — Laplace solution of an RLC circuit ​

A series RLC circuit with R=100\ \Omega, L=0.1 H, $C=10\ \mu$F is driven by a 10 V step at t=0, with zero initial conditions. Find v_C(t).

Solution

Set up in the s-domain as a voltage divider:

V_C(s)=\frac{10}{s}\cdot\frac{1/sC}{R+sL+1/sC}

Multiply numerator and denominator by sC:

=\frac{10}{s}\cdot\frac{1}{s^2LC+sRC+1}=\frac{10}{s}\cdot\frac{1/LC}{s^2+\frac RLs+\frac{1}{LC}}

Numbers.

\frac{1}{LC}=\frac{1}{0.1\times10^{-5}}=10^6, \qquad \frac RL=\frac{100}{0.1}=1000

V_C(s)=\frac{10\times10^6}{s(s^2+1000s+10^6)}

Identify the standard form. \omega_n^2=10^6 so \omega_n=1000 rad/s. And 2\zeta\omega_n=1000 so \zeta=0.5 — underdamped, so expect ringing with about 16% overshoot.

Poles:

s=\frac{-1000\pm\sqrt{10^6-4\times10^6}}{2}=-500\pm j866

so \omega_d = 866 rad/s = 138 Hz.

Partial fractions.

\frac{10^7}{s(s^2+1000s+10^6)}=\frac{A}{s}+\frac{Bs+C}{s^2+1000s+10^6}

A by cover-up: A = 10^7/10^6=10.

Multiply through and match: 10(s^2+1000s+10^6)+s(Bs+C)=10^7. Comparing s^2: 10+B=0, so B=-10. Comparing s: 10{,}000+C=0, so C=-10{,}000.

V_C(s)=\frac{10}{s}-\frac{10s+10{,}000}{s^2+1000s+10^6}

Complete the square in the denominator: (s+500)^2+866^2.

Rewrite the numerator to match the standard pairs:

10s+10{,}000 = 10(s+500)+5000 = 10(s+500)+5.774\times866

V_C(s)=\frac{10}{s}-10\cdot\frac{s+500}{(s+500)^2+866^2}-5.774\cdot\frac{866}{(s+500)^2+866^2}

Invert term by term:

v_C(t)=10-10e^{-500t}\cos(866t)-5.774e^{-500t}\sin(866t)

Combine into a single sinusoid: amplitude \sqrt{10^2+5.774^2}=11.55, phase \arctan(5.774/10)=30°:

v_C(t)=10-11.55\,e^{-500t}\cos(866t-30°)\ \text{V}

Checks. At t=0: 10-11.55\cos(-30°)=10-11.55(0.866)=10-10=0 ✓ (capacitor starts uncharged). Final value \to10 V ✓.

First peak at t=\pi/\omega_d=3.63 ms: v_C=10+11.55e^{-1.81}\cos(150°)... more directly, the standard overshoot formula gives 100e^{-\pi(0.5)/\sqrt{0.75}}=16.3\%, so the peak is 11.63 V — the capacitor briefly exceeds the 10 V supply. That is real and measurable, and it is why a component rated exactly at the supply voltage can fail in a lightly damped circuit.

Problem 9 — Poles, stability and response ​

A system has H(s)=\dfrac{10(s+2)}{(s+1)(s^2+4s+13)}. Find the poles and zeros, assess stability, and describe the impulse response without computing it.

Solution

Zero: s=-2.

Poles: s=-1, and from s^2+4s+13=0:

s=\frac{-4\pm\sqrt{16-52}}{2}=\frac{-4\pm j6}{2}=-2\pm j3

Stability: all three poles have negative real parts ✓ stable.

The response, read from the geometry:

  • The pole at -1 contributes e^{-t}, a decay with time constant 1 s.
  • The pair at -2\pm j3 contributes e^{-2t}\cos(3t+\phi) — ringing at 3 rad/s (0.48 Hz), decaying with time constant 0.5 s.

Which dominates? The pole at -1 is closest to the imaginary axis, so its term decays slowest. After about 1 second the ringing has largely gone and only the exponential remains. The pole at -1 is the dominant pole, and a first-order approximation using it alone would be reasonable for the late behaviour.

Damping of the complex pair: \omega_n=\sqrt{13}=3.61, and 2\zeta\omega_n=4 so \zeta=0.554. Overshoot around 12% if that pair acted alone.

Settling time governed by the slowest pole: t_s\approx4/1=4 s.

DC gain by setting s=0:

H(0)=\frac{10\times2}{1\times13}=1.54

so a unit step settles at 1.54.

All of that was read off the pole positions without inverting the transform. That is the point of the s-plane picture, and it is how a control engineer assesses a system in ten seconds.

Problem 10 — Z-transform of a difference equation ​

For y[n]=0.9y[n-1]+x[n]-0.5x[n-1]: find H(z), the poles and zeros, check stability, and find the impulse response.

Solution

Transform each term:

Y(z)=0.9z^{-1}Y(z)+X(z)-0.5z^{-1}X(z)

Y(z)(1-0.9z^{-1})=X(z)(1-0.5z^{-1})

H(z)=\frac{1-0.5z^{-1}}{1-0.9z^{-1}}=\frac{z-0.5}{z-0.9}

Zero at z=0.5; pole at z=0.9.

Stability: |0.9|\lt1 ✓ stable, but only just — a pole at 0.9 gives a slow decay.

Impulse response. Rearrange for the standard pairs:

H(z)=\frac{z-0.5}{z-0.9}=\frac{z-0.9+0.4}{z-0.9}=1+\frac{0.4}{z-0.9}

The second term is 0.4z^{-1}\cdot\frac{z}{z-0.9}, so it inverts to 0.4(0.9)^{n-1}u[n-1]:

h[n]=\delta[n]+0.4(0.9)^{n-1}u[n-1]

Check directly from the difference equation. With x=\delta: y[0]=1. y[1]=0.9(1)+0-0.5=0.4 ✓. y[2]=0.9(0.4)=0.36; formula gives 0.4(0.9)^1=0.36 ✓.

Time constant. The response falls to 1/e when 0.9^n=0.368, so n=\ln(0.368)/\ln(0.9)=9.5 samples.

Frequency response at DC (z=1):

H(1)=\frac{1-0.5}{1-0.9}=\frac{0.5}{0.1}=5

At Nyquist (z=-1):

H(-1)=\frac{-1-0.5}{-1-0.9}=\frac{-1.5}{-1.9}=0.79

Gain of 5 at DC and 0.79 at Nyquist — a low-pass filter, which matches the pole sitting at z=0.9, close to the DC point at z=1.

Problem 11 — Design a notch filter in the z-plane ​

Design a digital notch removing 60 Hz from a signal sampled at 600 Hz, with a notch width of about 6 Hz.

Solution

Angle of the notch:

\omega_0=2\pi\frac{60}{600}=0.2\pi=0.6283\ \text{rad/sample}

Zeros on the unit circle at that angle, to make the response exactly zero there:

z=e^{\pm j0.2\pi}, \qquad \cos(0.2\pi)=0.809

Numerator:

(z-e^{j0.2\pi})(z-e^{-j0.2\pi})=z^2-2(0.809)z+1=z^2-1.618z+1

Poles at the same angle, radius r, to narrow the notch. The relationship between r and the -3 dB width is approximately

\text{width} \approx \frac{(1-r)f_s}{\pi}

For 6 Hz:

1-r=\frac{6\pi}{600}=0.0314 \;\Rightarrow\; r=0.969

Denominator:

z^2-2(0.969)(0.809)z+0.969^2=z^2-1.568z+0.939

H(z)=\frac{z^2-1.618z+1}{z^2-1.568z+0.939}

As a difference equation:

y[n]=1.568y[n-1]-0.939y[n-2]+x[n]-1.618x[n-1]+x[n-2]

Verify at 60 Hz. z=e^{j0.2\pi} makes the numerator exactly zero, so the gain is exactly zero ✓.

Verify at DC (z=1):

H(1)=\frac{1-1.618+1}{1-1.568+0.939}=\frac{0.382}{0.371}=1.03

Nearly unity ✓ — the notch removes 60 Hz and leaves everything else essentially untouched.

Verify at 30 Hz (\omega=0.1\pi, z=e^{j0.1\pi}): working through gives a magnitude of about 0.86, so -1.3 dB. Acceptable — a signal component at 30 Hz loses 14%.

The trade to state explicitly. Moving r to 0.99 narrows the notch to 1.9 Hz, so nearby frequencies are barely touched. But the poles are then extremely close to the unit circle, and in 16-bit fixed-point arithmetic the coefficient rounding can push them outside, turning the filter into an oscillator. 0.97 to 0.99 is the practical range, and beyond it you need a cascade or higher precision.

Problem 12 — Aliasing analysis ​

A 5 kHz sine, a 12 kHz sine and 30 kHz of broadband noise are sampled at 20 kHz with no anti-alias filter. What appears in the output? Design the filter that would prevent it.

Solution

Nyquist is 10 kHz.

5 kHz: below Nyquist, appears correctly at 5 kHz.

12 kHz: |12-20|=8 kHz. Appears at 8 kHz — a tone that was never present.

Noise up to 30 kHz: every component folds. 10 to 20 kHz folds down to 10 to 0 kHz; 20 to 30 kHz folds up from 0 to 10 kHz. The entire 0 to 10 kHz output band receives three overlapping copies of the noise.

Noise power in the band is therefore three times what it would be with proper filtering, which is a 4.8 dB penalty — nearly one bit of resolution thrown away by a missing filter.

Design the anti-alias filter. Suppose the signal of interest is 0 to 5 kHz and we want anything above 10 kHz down by 60 dB.

Transition from 5 kHz to 10 kHz is one octave. Roll-off needed is 60 dB per octave, and each filter pole gives 6 dB per octave:

n=\frac{60}{6}=10\ \text{poles}

A ten-pole analog filter is a serious and expensive piece of hardware, with poor phase behaviour and components that must be accurate to a fraction of a percent.

Now oversample by 8, sampling at 160 kHz. Nyquist becomes 80 kHz. The transition is 5 kHz to 80 kHz — exactly 4 octaves:

n=\frac{60}{6\times4}=2.5 \;\to\; \textbf{3 poles}

A three-pole Butterworth, which is one op-amp and five passive components. Then apply a steep digital filter and decimate by 8.

The whole design decision in one line: eight times the sample rate turned a ten-pole analog problem into a three-pole one. Digital filtering is cheap; analog precision is not.

Problem 13 — Reconstruction and the zero-order hold ​

A DAC runs at 48 kHz with a zero-order hold. Find the attenuation at 5 kHz, 15 kHz and 20 kHz, and say what compensation is needed.

Solution

|H(f)|=\left|\text{sinc}(f T_s)\right| = \left|\frac{\sin(\pi f/f_s)}{\pi f/f_s}\right|

At 5 kHz: \pi(5/48)=0.327 rad.

\frac{\sin(0.327)}{0.327}=\frac{0.3212}{0.327}=0.982 \;\Rightarrow\; -0.16\ \text{dB}

At 15 kHz: \pi(15/48)=0.982 rad.

\frac{0.8315}{0.982}=0.847 \;\Rightarrow\; -1.44\ \text{dB}

At 20 kHz: \pi(20/48)=1.309 rad.

\frac{0.9659}{1.309}=0.738 \;\Rightarrow\; -2.64\ \text{dB}

Almost 3 dB down at the top of the audio band — clearly audible as a dull top end.

Compensation. Apply a digital filter with the inverse response, boosting by 1/\text{sinc}(fT_s) across the band. This is free — it is a few extra filter taps — and it is why converter datasheets list "sinc compensation" in the digital filter block.

Oversampling helps here too. Running the DAC at 8× (384 kHz) and interpolating means 20 kHz is at \pi(20/384)=0.164 rad:

\frac{0.1633}{0.164}=0.9955 \;\Rightarrow\; -0.04\ \text{dB}

Negligible. So oversampling fixes three problems at once — a gentle reconstruction filter, negligible sinc droop, and better in-band noise. That combination is why every audio converter made since the late 1980s oversamples.

Problem 14 — Undersampling a radio band ​

A signal occupies 98 to 102 MHz. Find sampling rates that capture it without aliasing, and state the practical constraints.

Solution

Bandwidth: 4 MHz. Naive Nyquist would demand 204 MSPS. Bandpass sampling can do far better.

The condition is

\frac{2f_H}{k}\le f_s\le\frac{2f_L}{k-1}

with f_L=98, f_H=102 MHz.

k=25: \dfrac{204}{25}=8.16 \le f_s \le \dfrac{196}{24}=8.167 MHz. Valid but the window is 7 kHz wide — far too tight for a real clock.

k=20: \dfrac{204}{20}=10.2 \le f_s \le \dfrac{196}{19}=10.32 MHz. A 120 kHz window, workable.

k=12: \dfrac{204}{12}=17 \le f_s\le\dfrac{196}{11}=17.82 MHz. An 820 kHz window — comfortable.

Take f_s=17.4 MSPS. The band aliases down to

98-5\times17.4=98-87=11\ \text{MHz to } 102-87=15\ \text{MHz}

Hmm — that exceeds Nyquist of 8.7 MHz, so fold again: 17.4-11=6.4 and 17.4-15=2.4. The band lands at 2.4 to 6.4 MHz, inverted, comfortably inside Nyquist ✓.

The three practical constraints:

  1. The sample-and-hold needs 102 MHz of analog bandwidth, even though it samples at 17.4 MSPS. A converter with a 10 MHz input bandwidth simply will not see the signal.

  2. Jitter is set by the input frequency, not the sample rate. From Chapter 3.5, for 12 bits at 102 MHz:

t_j\lt\frac{1}{2\pi\times102\times10^6\times4096}=0.38\ \text{ps}

Sub-picosecond, which needs a dedicated low-noise clock, not a microcontroller output.

  1. A bandpass filter before the sampler is compulsory, and now it must be a bandpass, not a low-pass — anything outside 98 to 102 MHz will alias into the band and there is nothing to distinguish it afterwards.

Payoff: 17.4 MSPS instead of 204 MSPS is a twelvefold reduction in data rate and converter cost. That is why every software-defined radio does this, and why the specification that matters on such a converter is its analog input bandwidth rather than its sample rate.


Part 5 takes the transforms of this Part and makes them computable, starting with the algorithm that made digital signal processing possible at all.

Combine chapters into one PDF

Pick the chapters you want. They print in the order you pick them.

Volume III — Electronics & Communication
Part 1 — Circuit Theory
Part 2 — Devices & Analog Circuits
Part 3 — Digital Electronics
Part 4 — Signals & Systems
Part 5 — Digital Signal Processing
Part 6 — Control Systems
Part 7 — Communication Systems
Part 8 — Wireless & Telecom in Practice
Part 9 — Power Electronics & Machines
Part 10 — Embedded Systems & the Smartphone
Nothing picked yet